Search Results for ‘wiring’

1997 TL1000S "V" Fault: Low voltage reading through pressure sensors With ignition "ON" voltage checked with voltmeter between RED(+) - Black/Brown(-), voltage reading shown as 0.23V The manual shows the voltage as being between 4.5V-5V.. My pinout for the electrical connector on the IAP...

Good day all, having problems with my tl1000s' headlights... We recently opened the wiring and found that the wiring was melted from the light switch to the yellow box connector. We replaced the wires and all worked fine... Took bike for a drive about 10km or so today... Once returning home the...

Tired of searching so wondering if someone could send a link to where i buy the yellow plug that is being the left side of the headlights that a lot of people replace or tell me exactly which one to buy from easterbeaver.com also i assume i needed to solder this connection? Thanks in advance

I am putting my TLR back together and I can seem to remember how the headlight/fuse box harness wiring was routed. I also need to find out how the cables(throttle) are routed around the forks! I have looked at the manual and of course it really doesn't help. So if anyone out there has their...

Im about to put my tiller through a major upgrades and services. Question is does anyone know where to get oem suzuki wire connectors or get wiring harness for the bike would like to prevent any future breakdowns and plan on my baby lasting till i cant ride no more lol

Do i need to drop motor to change main wiring harness on a tlr?What mods should be done to new harness going in? :O

this one goes up from the neutral unit and the small black one that goes from the front witing loom this is the wiring , maybe you can point me thanks! :)

HELLO PEOPLE Gotta a minor prob-putting a new cone on the front of the bim- as i pulled all the brains-powercommander electrics etc some wires disconnected and i'm fcked if i know where they go-i'm pretty sure they are to do with fuel injection.What i can tell ya is that 8 years ago we ditched...

I installed my projector so I could ride while I finish up my project bike. I have my projector to the low beam and the other to the high beam. My problem is when I flip the high beam on the projector goes off. :confused I put a jumper in the projector connection from both low and high beam...

I've started my HID conversion. I've got to the Angel Eyes installation which run off the side lights. The side light has two wires, a brown and black/white coming from it. While my HID wires are black and red. I assume, Brown to Red And black/white to Black or does it even matter...

I changed my 97 TL1000S into a TL1000R and have some wiring issues with the Gauge Cluster. I went from the S cluster to the R cluster but the pin locations are not the same. Does anyone know how to wire this up ?? Or maybe someone makes an adapter harness ?? Thanks for any help. Steve...

Lucas smoke

Sadly, I have to sacrifice the heart of my project and put everything on hold. My school's financial department just informed me that I owe $800.00 more than my loans will cover--my loss is your gain. :banghead This is a complete engine out of a running bike. Similar engines with all wiring...

Wire harness from a 2000 TLR. Good shape (does not include headlight harness). $110 OBO + actual shipping and insurance. Thanks, Chris

Hi, Im new to this forum having only just become a TLR owner and I could do with some help! The AP sensor, located by the headlight, has been ripped off by the previous owner. Unfortunately, it took the plug with it so I am only left with the 3 wires! I have got a new sensor but I dont know...

Helo lads, Right.... I`ve fitted a set of Renthal Fatbars to me TLS and i`ve done away with the clocks and rev counter... In it`s place now sits a nice tidy little KOSO Digital Speedo, but i`m wanting to keep the Oil light/Neutral light & Fuel light as they`re handy things to have. Can someone...

I'm doing the gsxr gauge conversion and would like a spare harness if anyone has one for a reasonable price

I have a 99 TLR that the previous owner had a hack job on. Normally that wouldn't have been a big deal...but he rewired the headlight to a toggle switch and pulled the wires clear out of the main wiring harness going to the dimmer switch plug. I bought the new left hand control, but the wiring...

Preliminary: I bought & installed flash2pass garage door opener system (Great system incidentally - no more carrying remote and fumbling for it when returning - installed transmitters on all three bikes and one car to get rid of the visor clip-on) The other bikes worked great - what I found...

I have a GIPro that I want to switch on and off manually. Not sure if I am supposed to add a relay for this application but I included one in the diagram. Does this look correct? Do I even need a relay?