Search Results for ‘seals’

Ok. I need a set of seals for 6 pot calipers. All pistons are the same size. 26.9mm Who would be willing to check prices, and if need be order and ship them here. Who can get them the cheapest? Shipped to the UK mainland. :)

New to the site - and good manners would deem that i hang around in the background, place a few witty replies to threads before getting into the full swing of things. but i have a problem! One of the fork seals has gone, didn't just start weeping, but blew, spewed oil all over. trying to render...

I think I've identified leaking slave seals so going to change them as soon as I can get them. What I'd like to find out is should I replace the push rod as well?? If I do is it expensive and difficult or cheap and easy?? Nothing better to do on the weekend anyway,eh!! Cheers Jack

Needing a bit of help sourcing some seals for a couple of CO2 bulb powered airsoft pistols I have here. Since most pistols are illegal here, and in the UK CO2 powered devices fall under firearms (so no-one bothers with them), there's no real support network to get replacement parts. Hence I'm...

I just need to order the right parts. The fork seals are busted. On the link below what parts should I order to replace the seals? Do I need 2,4,5,6,7,8? http://i13.photobucket.com/albums/a270/camhops/forkseal.gif Regarding the link below. I'm missing a gasket between 1 and 4 and I'm...

hi again are all the oild seals in the crank caese replaceable form the out side? wanting to change as many as possible so when shes back together for the moto gp i have no issues thanks

Am i just blind or daft?? i cant find the part number for the mechanical seal on the fiche, i need the numbers for, the oil seal behind the clutch case, the metal bit for the mechanical seal that you can araldite in and the mechanical seal itself, this is mainly to all the folks who have done...

Several weeks ago I noticed the weep hole pissing again. Hadn't done the water/oil seals in about 10K so I figured it was time fix the ol pee pee. I ordered 2 sets of all the seals needed and continued riding a bit watching the water level. Well a week later I'm thinking it was a stupid...

.... and how long of a job is it to change them?? I have a track day on the 6th of April so need to get them done before then,, and only have the weekends free,, do i need any special tools to do it with?? Thanks.

is it normal for my tlr fork seals to start puking at about 8,000 mile intervals? yes i have the tools and skills plus the manual to do it properly,are there any "tricks" that will make them have a normal life? i have never changed the bushings but they look ok..any input??,.... i say,tank you !!!!

hey all. reaplaced my water pump seals along with all washers, gaskets and o-ring as i had coolant leaking from the drain hole. thought it was all sweet, but today.....started it up went for a little ride and i have a very small amount of oil coming from the drain hole! :banghead is this just a...

I was wondering if anyone could tell me if the TLR and TLS forks use the same oil seals?

well to make long story short....i discovered today that there is a way to ride while waiting for the local shop to order a new output shaft oil seal... answer..... go to local auto shop and pick up CR#14705 oil seal...although it is only a single lip seal ...it will fit into the hole left by...

I'm quite certain I'm leaking oil from the push rod seal and right behind the front sprocket. I'm sure many of you had already done this. I'm not very mechanically inclined but I'm going to try to tackle this one on my own. 1) I don't have a rear stand can I still do this repair? 2) I have...

Hey Gang!!!!!!!!!!!!!!!!!!!!!!! Doing a new sprocket/ chain... going 530 and steel 17/41(42) Whats the min tensile stength chain needed for these torque monstes?????? Stock eng. w/ V&H cans, lowerd gearing comming and I'm 6'4"-270lb.,not a wheelie or "drag racer". I see about 9300lb to 10,600...

I paid somebody to do it on my old bike... 96ZX6R. How hard is it to do on one of these babies?

anyone got the part numbers for the plastic and the rubber seals ? coolant leak out the weep hole have the ones that sit on the front of the inpellar right under the boly