TLZone Forums banner

question...

  1. Suzuki TL1000R & TL1000S Forum
    Are there other exhaust cans that fit on the TL (same flange)?
  2. Open Forum
    So I'm planing take my bike to the track. I have all I need except the suit. Is any advantage to a suit from one brand to another? I picked 3 suits as my options: -All 3 are made out of 1.2-1.4 leather -All 3 have full frontal perforated panels -All 3 have back protective humps -All 3 are...
  3. Open Forum
    What does it typically cost to get a set of carbs cleaned/rebuilt? No silly not for the Tiller....for my GSXR1100....the bike won't run without the choke being on and even then it spits and sputters at low RPM's....once over 288-3000 rpm's it runs good....has fresh gas.....but have never had it...
  4. Suzuki TL1000R & TL1000S Forum
    I would like to know if the people with Yoshimura RS-3 cans are running them with or without the baffles installed? Also why, do you notice any performance gain or just like the sound?
  5. Suzuki TL1000R & TL1000S Forum
    I just put on an RK 530 gold rx-ring chain and had to adjust it twice in about 400 miles. The sprockets didn't show any wear signs so I only did the chain. My question is what is considered normal stretch for a new chain for a 215 lb rider that likes power wheelies? I see no reason to slip the...
  6. Suzuki TL1000R & TL1000S Forum
    Right, The lower bolt holding in the rear damper on my 98 tls went missing. I ordered one from the local Suzuki dealer, it came in and I went to fit it. It slid straight in and didnt seem to touch any threads. (60 mm long) I took out the top bolt and tried it, and it went right right in and...
  7. UK Forum (Including Scotland)
    Just been offered a set of mint rear plastics for my S but the problem is that they have been drilled for the OE grabrail. So my question is this, do Suzuki make any rubber grommets as an OE fitment that plug the holes for when you take the rail off? Failing that, how much is a Suzuki...
  8. Suzuki TL1000R & TL1000S Forum
    I've recently noticed a few TLS's with their front end lowered by dropping the yokes on the forks slightly, and am considering doing it to mine (purely for aesthetic reasons). My main concern however, is how does this affect the handling of the bike? Obviously the TLS is quite twitchy anyway...
  9. Suzuki TL1000R & TL1000S Forum
    I want to do something with the frame and swinger on my Tiller but i can't decide between satin black or mirror polish? Oh, it's a 99 Yellow scheme
  10. Suzuki TL1000R & TL1000S Forum
    I know this is a question already asked but I need the info. Are there any problems I should look for regarding this mod? Or will this be as simple as it reads? It seems like everyone has done this mod but i have not read anything about any problems with the mod. Any info will be greatly...
  11. Suzuki TL1000R & TL1000S Forum
    Will the stock undertray fit if I have an aftermarket undertail:confused? I currently have a custom undertail but have nowhere to put the ECU, rectifier, etc..Id rather put the stock tray in there, but if it wont fit, Ill have to fab something up with some sheet metal I guess:O
  12. Suzuki TL1000R & TL1000S Forum
    ok so i have some projectors off of an infiniti. they are pretty big, also have the ballasts and all the wires for the power leads. id say they are about 10-12 ga wires for power. anyhow, each ballast had a 15 amp fuse going to them so my question is would my TLR be able to supply 30 amps of...
  13. Suzuki TL1000R & TL1000S Forum
    Quick Question... Tundra Truck & length of a TL1000r? I'm buying a Tundra, and not sure if the Crew Max model, the short bed will carry (in the bed) a TL1000r with the gate up. Could someone measure and let me know? Thanks! :)
  14. Suzuki TL1000R & TL1000S Forum
    Hi! Can anybody tell what is the purpose of this hose, and where it should be connected?
  15. Suzuki TL1000R & TL1000S Forum
    previous owner jb welded around the fuel pump... is this tank worthless now? or would it be ok to chisel that off or something?
  16. Suzuki TL1000R & TL1000S Forum
    I removed the PAIR system this past weekend but it was still popping/backfiring. So I went ahead and replaced the spigot and joint gaskets. About 1/4th of the spigot gasket looked like it was burnt out and the joint gasket looked well used. New gaskets fixed the problem and it wasn't too bad...
  17. Suzuki TL1000R & TL1000S Forum
    OK.. ..so I have my shock... I have my 1150 lb spring... I have my new spring seat made... ...so now I need to grind this tab... ...and I need to know if I am suppose to grind all of it off or just 1/4" of it.. ..if I take it all of that would seem to remove any possibility of...
Top