TLZone Forums banner

install

  1. Bitubo wrench?

    Suzuki TL1000R & TL1000S Forum
    What wrench do you all had to adjust the spring compression ring? Is a 2-1\2" spanner wrench the correct tool? I just had my Bitubo rebuilt and want to compress the spring before install, as I'm guessing it would be easier to loosen once on the bike.
  2. HELP!!!! Bitubo removal problem

    Help Forum
    Hi all. I'm trying to remove the Bitubo unit from my TLS to install a new spring. I can't get the unit out! I have removed the engine / frame spacer. I can't slide the unit out without crimping the hose, and I there is doesn't seem to be enough room to slide the reservoir out first before the...
  3. Pedrodani GPI install - wire colors

    Suzuki TL1000R & TL1000S Forum
    Hi guys, spent about one hour surfing the zone to find the instructions for the pedro GPI... i didn't find them, and pedro's site is offline. Does anybody remember which color wire is what? and how to connect it to the GPS? cheers, TA! Jan
  4. Proofreading Help for TRE Install Instructions

    Suzuki TL1000R & TL1000S Forum
    Greetings fellow Zoners, I'm finally getting around to finishing off the install instructions for the TRE-3 Timing Retard Eliminator I've been offering. Would any of you who have installed a three-wire TRE on their TLR or TLS be willing to give a quick look through my instructions to make sure...
  5. penske install

    Bike Pictures
    Cant wait to get this finished:) :devious
  6. Bitubo install

    Suzuki TL1000R & TL1000S Forum
    First I had to remove the back wheel and prop up the frame with some 3/4 inc extenstions and some jack stands. My rotory dampner was completely tore off the frame.
  7. FUEL PuMp install

    Suzuki TL1000R & TL1000S Forum
    K guys i get my tank Saturday:) and i bought a new fuel pump gasket and i cant wait until Saturday this will be the first time i actually get to start the bike since i bought it abut two weeks ago anyway i was hoping that some one could tell me the sequence of tightening the bolts and torq specs...
  8. Decal install help

    Suzuki TL1000R & TL1000S Forum
    Hey everyone, doing the Gulf racing tribute on my TLR, got the paint and powder coat done, now I got some cool Gulf Vinyl decals from the chaps in merry old England. I don't want to "F" them up, I have heard everything from 5 drops Palmolive/1 cup water, to windex, to the auto body shop trying...
  9. Pc3 install HELP!!!

    Suzuki TL1000R & TL1000S Forum
    Ok so i just got my TLR running again now i want to hook up the pc3 that the guy handed me when i bought the bike..... So can someone help me figure out how to install it on my 2002 tl1000r.
  10. TRE Mod Purchase and Install

    Suzuki TL1000R & TL1000S Forum
    Hello all, I am going to order and install a TRE mod for my 1999tlr. Any suggestions as to were I can buy the best quality TRE for my bike? I see so many different kinds on ebay and websites, they all claim to be the best. Should I also look into an aTRE? If anyone has tips or links to...
  11. TLR Ohlins install + Tip Over Sensor

    Help Forum
    Hey guys (and gals), Finally, after convincing myself to put the R back together rather than part it out and the games begin yet again. I installed my Ohlins (with all the bracketry) but now, for some god unknown reason, I can't put the tank back on because the TOS hits the Ohlin's brackets...
  12. Trying to install my ride height adjuster

    Suzuki TL1000R & TL1000S Forum
    I'm in the middle of lowering & extending my bike & i was wondering if anyone knew how far down you could actually lower a TLS with a r.h.a.I bought it from ziggy and he had said that in order to lower the bike one inch you have to cut 3.5 screws off of the end of the r.h.a.If this lowers the...
  13. How to install PC II on TLS without c14 TPS Code

    Suzuki TL1000R & TL1000S Forum
    I was trying to install a PCII on the TLS and I had a couple of issues. When I pluged it in grounded it and turned the ignition on I got a c14 and noticed my TPS was high. Without the PCII the c14 (TPS CODE) isnt there but the TPS columb is still high. The led on the PCII doesnt illuminate But...
  14. Veypor Install / Tach Question

    Suzuki TL1000R & TL1000S Forum
    So I got one of the nifty little Veypor gauges for my TLS fighter. The manual says to get the RPM info from the wires on ignition coil. So this brings two questions to mind: 1) Which wire on the coil should I tap to use for this info? I'd hate to accidentally use the wrong one and ruin a...
  15. daytona gauge install

    Suzuki TL1000R & TL1000S Forum
    i'm installing the daytona gauge... where is the best place to power this baby up from and also the the best place to earth it out... cheers
  16. 1/5 install question

    Suzuki TL1000R & TL1000S Forum
    hay guys and gals i just got my 1/5 from rifleman (THANK YOU THANK YOU THANK YOU):hail:hail:hail:hail:hail:hail:hail but i got no idea how to install it:confused:confused:banghead:banghead:banghead its prob so easy but i rather get help so i do it the right way:):) can someone take me...
  17. gi pro install

    Suzuki TL1000R & TL1000S Forum
    has anybody got any pics of how the connetion end of the 1997 tls gi pro should look like, just need to visualise it to get my head straight? :banghead:banghead cheers mad mat
  18. Anyone install a Trail Tech Vapor yet?

    Suzuki TL1000R & TL1000S Forum
    Hey Zoners, I just rec'd my Trail Tech Vapor for my TLR. Planning on installing soon, but was curious if anyone has ever followed through on this? Yes, I have run the search, and there were some posts, but everyone was just "looking" at them, no one seemed to have bought one thus far. So any...
  19. hid install ?????

    Suzuki TL1000R & TL1000S Forum
    i want to put projecter lights in my tls and but can find a thread that explains the install in detail. what projectors to buy,brackets templets and metal used, where there getting clear lenses. thanks for the help ahead of time.
  20. frame slider install

    Help Forum
    i bought some no-cut frame sliders but i cannot find the place to mount on the left side of the bike. do i have to replace another screw?
Top